News

Electro-Hydraulic CNC Press Brake: Core Structure and Selection Guide

Choosing an electro-hydraulic CNC press brake involves much more than comparing tonnage, bending length and machine price.

The essential difference from conventional torsion-shaft press brakes lies in the closed-loop servo
control architecture—it transforms the equipment from “open-loop mechanical synchronization” to “real-time dynamic feedback correction”, thus delivering significant advantages in batch consistency, complex workpiece forming, and automation integration.

For sheet metal fabricators, the real value of a press brake depends on whether it can repeatedly produce the required angle, flange dimension and bending radius under changing material, load and production conditions. A machine with sufficient nominal tonnage may still deliver inconsistent parts if its synchronization system, frame rigidity, crowning device, tooling or backgauge configuration is unsuitable.

This guide explains the main structure of an electro-hydraulic servo press brake and shows industrial buyers how to select the right machine according to material thickness, bending length, workpiece geometry, production volume and automation requirements. The technical structure and inspection points are based on the uploaded electro-hydraulic press brake selection manual.

Electro-hydraulic Servo CNC Press Brake

Overall Appearance of Electro-hydraulic Servo CNC Press Brake

What Is an Electro-Hydraulic CNC Press Brake?

An electro-hydraulic CNC press brake is a hydraulic sheet metal bending machine that uses independently controlled hydraulic cylinders, CNC commands and position-feedback devices to control the movement of the ram.

The left and right hydraulic cylinders are normally identified as the Y1 and Y2 axes. Linear encoders or magnetic scales continuously measure the actual ram position on both sides. The CNC controller compares the measured position with the programmed position and sends correction signals to the proportional servo valves.

This closed-loop control architecture allows the machine to correct synchronization errors during the bending process instead of relying only on mechanical linkage.

Electro-Hydraulic Press Brake vs. Torsion-Bar Press Brake

ComparisonElectro-Hydraulic CNC Press BrakeTorsion-Bar Press Brake
Ram synchronizationIndependent Y1/Y2 closed-loop controlMechanical torsion-shaft synchronization
Position feedbackLinear encoders on both sidesNormally limited or indirect feedback
Eccentric-load controlBetter automatic correction capabilityMore sensitive to uneven loading
Angle consistencySuitable for precision and batch productionSuitable for general bending work
CNC functionsMulti-axis control, graphic programming and compensationUsually fewer axes and simpler programming
Long-workpiece bendingBetter when combined with CNC crowningMore dependent on manual adjustment
Automation integrationEasier to connect with robots and production linesGenerally limited
Typical applicationsPrecision parts, long plates and complex componentsBasic brackets and general fabrication

A torsion-bar machine may remain economical for simple workpieces and lower production requirements. However, an electro-hydraulic CNC press brake is normally the better choice when the factory requires repeatable angles, complex bending sequences, long components, multiple product varieties or future automation.

1. Electro-Hydraulic Servo Closed-Loop System

This system serves not only as a power source but also as the central execution unit for precision control, with its operational closed-loop process comprising three hierarchical stages:

  • Command Layer: The CNC system (e.g., DELEM DA-66T) calculates the target bottom dead center position and bending force curve based on workpiece parameters, then outputs analog voltage/current signals to the servo valve.
  • Execution Layer: The electro-hydraulic proportional servo valve (e.g., Rexroth 4WRKE) receives commands to dynamically adjust the oil flow and back pressure of the left and right cylinders at high speed, driving the slider downward along the guide rail. The left and right cylinders (axes Y1/Y2) are independently supplied with oil, eliminating forced synchronization errors caused by mechanical linkages.
  • Feedback layer: High-resolution grating scales (e.g., Heidenhain LC series, resolution 0.5 μm) or magnetic scales are mounted at both ends of the slider to measure actual position in real time. The data is transmitted to the controller at millisecond intervals, compared with the target value via PID control, and a correction signal is generated to form a fully closed-loop system.

Key Technical Parameters:

  • Slider repeatability accuracy: ±0.01–±0.02 mm (depending on grating precision and servo valve response frequency, typically ≥200 Hz).
  • Consistency tolerance of bending angle: ±0.25° to ±0.5° (for workpieces up to 2 m in length).
  • Eccentric load capacity: The dual-cylinder independent closed-loop system enables automatic leveling of the slider under eccentric loads (e.g., single-side short-edge bending), with a tolerance up to 30% of the rated tonnage—significantly better than mechanical synchronization systems (≤10%).

Core Component Selection Recommendations:

Rexroth Electro-hydraulic Proportional Servo Valve
Rexroth Electro-hydraulic Proportional Servo Valve

Rexroth Electro-hydraulic Proportional Servo Valve

Heidenhain High-precision Linear Encoder
Heidenhain High-precision Linear Encoder

Heidenhain High-precision Linear Encoder

  • Servo valve: Preferably choose nozzle-baffle type or jet tube type, as they offer superior anti-contamination performance compared to direct-acting types; imported brands (Rexroth, Moog, Parker) exhibit rapid response, while domestic alternatives require attention to hysteresis and zero drift specifications.
  • Displacement sensor: Grating scales are suitable for clean environments, while magnetic scales offer strong resistance to oil contamination; the latter is preferred in factories with high dust levels.
  • Hydraulic integration block: Combines plug-in valves with tandem valves to minimize pipeline leakage points, with response latency controlled within 20 ms.

How to Verify a Genuine Closed-Loop Machine

Before purchasing, buyers should inspect the machine instead of relying only on the words “servo” or “CNC” in the quotation.

Check whether:

  1. Independent position sensors are installed on both sides of the ram.
  2. The sensors are connected to the CNC closed-loop feedback system.
  3. Y1 and Y2 values can be viewed or diagnosed independently.
  4. The hydraulic valves support accurate dynamic flow control.
  5. The machine can correct ram synchronization under an uneven load.
  6. The supplier can demonstrate repeatability through an actual bending or positioning test.

A machine with only a torsion shaft, limit switches or a single position sensor should not be considered equivalent to a full Y1/Y2 electro-hydraulic closed-loop press brake.

2. Rigid Structure of the Machine Frame and Workbench

All dynamic accuracy ultimately depends on static stiffness. The body design of an electro-hydraulic bending machine must balance both static stiffness (bending resistance) and dynamic stiffness (vibration resistance), with the key structural components outlined below:

  • Overall welded frame: Constructed from Q690D or HG785 high-strength steel, with plate thickness typically ranging from 25 to 40 mm (depending on load capacity). Post- welding, the frame must undergo two aging treatments: initial full annealing to eliminate welding stresses, followed by vibration stress relief (VSR) to stabilize residual stresses, ensuring deformation within ≤0.05 mm/m over five years. The spliced body (bolted connection) exhibits a stiffness loss of approximately 15%–20%, and should be used with caution in applications requiring high precision.
  • Deflection Compensation System: This is the “invisible precision core” of the electro- hydraulic bending machine: 3 to 9 independent hydraulic cylinders are installed beneath the worktable (depending on the machine length). During bending, the CNC system automatically calculates a compensation curve based on plate thickness, material, and die opening, lifting the center of the worktable to compensate for the deflection deformation of both the compensating slider and the worktable at the center point.

The compensation amount can be dynamically adjusted, with a maximum compensation range typicallyranging from 0.5 to 2.0 mm (depending on load capacity). Compared to mechanical crowning (fixed pre-arc), hydraulic compensation adapts well to varying load conditions and significantly improves angular consistency for long workpieces (≥3 m); the angular deviation between left, middle, and right sides of the same workpiece can be reduced from ±1.5° to ±0.3°.

  • Enhanced rib topology optimization: Modern design employs finite element analysis (FEA) to install inclined ribs in high-stress areas of sliders, wall panels, and bases, increasing torsional stiffness by over 30% and preventing angular deformation of sliders under eccentric loads.

Internal Structure of Hydraulic Deflection Compensation Table

Internal Structure of Hydraulic Deflection Compensation Table

3. CNC and Backgauge Positioning System

CNC System Levels: Industrial-grade dedicated bending CNC systems (e.g., DELEM 60 series, CYBELEC Vision series) feature the following advanced capabilities:

  • Material Database: Includes tensile strength and rebound coefficients for over 500 types of plates (stainless steel, aluminum, titanium alloys, etc.), with automatic calculation of lower dead point compensation values.

  • 3D graphics programming: Supports direct import of DXF drawings, automatically identifies bending sequences and interference zones, simulates the forming process, and eliminates trial bending waste.

  • Real-time angle correction: When used with an angle measuring instrument (e.g., laser angle meter), the system automatically adjusts the material blocking position and compensation force after the initial fold test, eliminating manual intervention for subsequent batches.

  • Multi-tasking: Supports simultaneous background programming and front-end processing, reducing die changeover downtime.

Backgauge Mechanism (X-R-Z Axis Combination):

DELEM DA-66T Touch Screen CNC Control System

DELEM DA-66T Touch Screen CNC Control System

  • X-axis (front-to-back): servo motor + precision ball screw (Class C3) + linear guide (e.g., THK SRG), with positioning accuracy of ±0.01 mm and repeatability of ±0.005 mm.
  • R-axis (up/down): Controls backgauge finger height to accommodate varying plate thicknesses and prevent collisions with the die.
  • Z-axis (left/right): Independent servo drive with automatic segmented indexing, ideal for rapid positioning in multi-edge bending or workpieces of varying lengths.
  • The high-end configuration further includes independent Z1/Z2 axes, enabling separate movement of left and right finger guides to meet positioning requirements for conical or irregularly shaped workpieces.

CNC Backgauge Mechanism

CNC Backgauge Mechanism

4. Upper and Lower Die Assembly

  • Upper die structure: Segmented design (standard segment lengths of 835 mm or 415 mm), allowing assembly as needed and individual replacement of worn sections to reduce costs. Clamping methods include hydraulic clamping (for rapid die changeover) and
  • mechanical clamping (providing better rigidity); hydraulic quick-clamping is recommended for frequent die changes.
  • Lower die groove selection: The opening width of the lower die’s V-shaped groove should typically be 8–12 times the plate thickness (standard); for precision bending, a width of 6 times the thickness may be used to reduce the corner radius. The lower die should feature dual-V or quadruple-V grooves for quick switching.
  • Die Materials and Heat Treatment: Common materials include Cr12MoV (high-carbon, high-chromium steel) or LD steel (7Cr7Mo2V2Si), which undergo vacuum quenching and cryogenic treatment to achieve a hardness of HRC 58–62, excellent toughness, and resistance to chipping. The surface can be coated with PVD layers (TiN or TiAlN), reducing the friction coefficient below 0.2, minimizing material scratching, and extending service life by 2–3 times. Low-cost dies with hardness below HRC 55 (e.g., hardened 45# steel) exhibit extremely rapid wear rates in mass production, requiring grinding after every 1,000 units; therefore, they are not recommended for mass production lines

Upper and Lower Die Assembly for Press Brake

Upper and Lower Die Assembly for Press Brake

Precise Selection of Practical Techniques

Tip 1: Servo System – Distinguish genuine full closed-loop systems from counterfeit systems to prevent conceptual confusion

  • Identity Verification: Inspect the installation of independent displacement sensors (grating scale/magnetic scale) on both sides of the slider, and confirm that the sensor signals are connected to the closed-loop feedback port of the CNC system. If only a mechanical synchronization shaft (torsion shaft) or a single main position sensor is present, this constitutes a “open-loop + limit switch” configuration. While the angle can be adjusted via the CNC screen, it cannot achieve dynamic alignment correction for both cylinders; the bending angle is significantly affected by oil temperature and load fluctuations (tolerance typically> ±1°).
  • Valve configuration: Preferentially select servo valves with spool position feedback (i.e., closed-loop valves), which have a hysteresis of <1%, offering one order of higher accuracy than conventional proportional valves (hysteresis 3–5%).
  • Oil circuit design: Verify the inclusion of a accumulator and pressure compensator—the former ensures smooth slider movement during emergency stops, while the latter mitigates velocity fluctuations caused by hydraulic pump pulsation.

Tip 2: Body rigidity – focus on “material quality” and “construction craftsmanship” rather than tonnage

  • Tonnage margin calculation: Bending force formula (empirical): P = (1.42 × σ_b × S²× L) / V, where σ_b is the tensile strength (MPa), S is plate thickness (mm), L is bending length (m), and V is the die opening size (mm). After determining the required tonnage, a 20%–30% margin must be added—because prolonged operation at rated tonnage causes plastic deformation in the body and significantly reduces the service life of seals and oil pumps (operating life under rated pressure is approximately half that under 80% load).
  • Process validation method: The manufacturer must provide a body aging treatment report (including annealing temperature curves and vibration aging frequency records). For existing models, the lower dead center offset of the slider under no-load and full-load conditions (80% capacity) can be measured using a laser interferometer; if the offset exceeds 0.03 mm/1000 mm, the rigidity is insufficient.
  • For long workpieces (≥3 m): A hydraulic deflection compensation system must be installed, with at least (machine tool length/m) × 2 + 1 compensation cylinders required. Pure mechanical compensation methods (e.g., wedge-type crowning mechanisms) employ fixed curves that cannot adapt to varying plate thicknesses; the angular deviation between the workpiece ends and the center often exceeds 0.8°, which is unacceptable.

Tip 3: CNC System and Number of Axes – Select models based on the machining diagram to avoid “over-functionality”.

Create a selection decision table:

Processing ScenarioRecommended CNC GradeNumber of Backgauge AxesKey Assistance Features
Large-scale production of a single variety (e.g., standard scaffolds)Basic Type (DE15)X+R (3-axis)No graphicalprogramming required; enter manually
Small to medium-sized batches, multiplevarieties (standardcomponents for sheet metal workshops)Standard Type (DA- 53T)X + R + Z (3-axis)Graphicalprogramming, anglecorrection, and process storage capacity ≥ 100 sets
Complex and irregular- shaped components;precision parts for aviation/medical applicationsHigh-end model (DA- 66T or Cybelec Touch)Axes 4–6 (including Z1/Z2 and auxiliary axes)3D simulation, online measurement,automaticcompensation, network interface (MES)
Fully Automated Production LineEquipped with a robot interface and remotediagnostic capabilities.Supports external axes simultaneouslyIntegrated with the automatedloading/unloading software package

Key Points to Avoid:

  • Niche CNC systems (e.g., those from certain domestic brands without open interfaces) have long maintenance cycles, high spare part costs, non-standard programming syntaxes, and pose recruitment challenges. It is recommended to prioritize the three mainstream systems: DELEM, CYBELEC, and ESA.

  • The touchscreen must be at least 10 inches in size; otherwise, operation of the programming interface will be inconvenient. It must also include a USB/Ethernet interface for easy program transmission and backup.

Tip 4: Hydraulic Systems and Die Details – The Key Factors Determining Hidden Costs

Long-life design for hydraulic systems:

  • The recommended main oil pump is an axial piston variable displacement pump (e.g., Rexroth A4VSO), which offers 10% higher efficiency and lower noise levels compared to gear pumps.
  • The sealing ring employs an FKM (fluororubber) or PTFE fabric-reinforced composite seal, with a temperature resistance up to 120°C and a service life three times that of conventional NBR.
  • A air-cooled or water-cooled cooler must be installed to maintain oil temperature stable between 40–55°C (a 10°C increase in oil temperature reduces seal lifespan by half and increases servo valve zero drift).

Economic Comparison of Die Selection:

Cr12MoV dies incur high initial costs (approximately 2.5 times those of conventional carbon steel), yet after 100,000 bending cycles, their total cost—including grinding expenses, downtime, and defect rates—falls by over 30% compared to carbon steel.

Throat depth and opening height – determined by workpiece geometry:

  • The throat depth (depth of the throat opening) must be ≥ the maximum bending edge height of the workpiece + 50 mm; otherwise, the formed wing edge cannot be accommodated.
  • The opening height (distance from the slider’s dead center to the worktable) must exceed the die closure height plus maximum plate thickness plus safety allowance (≥ 80 mm) to prevent collisions during workpiece handling.
  • For deep-box type workpieces (U-shaped or box-shaped), special attention must be paid to side-wall interference; if necessary, incorporate a rear stop relief function or die deflection mechanism.

Tip 5: Built-in Intelligent Interfaces (For the next 3–5 years)

  • Reserve ports for the online angle detection system (e.g., laser or mechanical contact angle measurement devices) to facilitate future upgrades to full closed-loop angle control (eliminating reliance on trial folding).
  • With the remote diagnostic module (supporting 4G/5G connectivity), manufacturers can remotely read logs and adjust parameters to reduce downtime caused by faults.
  • If you plan to integrate with an automated production line, ensure the CNC system supports OPC UA or Profibus/Profinet protocols to establish handshake communication with robots and feeders.

Comprehensive Acceptance List – Essential Items to Be Inspected Before Delivery

Inspection ItemTest MethodAcceptance Criterion
Slider Repeatability AccuracyThe laser interferometermeasured the lower dead center 10 times.bias in statistics ≤±0.02mm
Angle Consistency (3m Workpiece)Measure angles at the left, center, and right points.Range ≤ ±0.3° (within the same batch)
Eccentric Load CapacityLoad 50% of the tonnage on one side of the slider and measurethe offset on the other side.offset ≤0.05mm
Hydraulic System LeakageMaintain full load and pressure for 10 minutes, then observe the pressure drop.Pressure drop ≤ 2%
Compensation System ResponseEnter the compensation curveand use a micrometer to measure the protrusion on the workbench.The actual protrusion deviation from the set value is ≤5%.
Noise LevelOperated under no-load conditions, measured at a distance of 1 m.≤80dB(A)

Why Choose Pacific for CNC Press Brake Solutions?

Pacific supplies sheet metal processing equipment including plate rolling machines, leveling machines, press brakes, laser cutting machines and shearing machines. Its press brake range currently includes economic, cost-effective, high-performance and tandem CNC configurations.

The WE67K electro-hydraulic servo CNC press brake is designed with a welded machine structure, closed-loop servo synchronization, grating-ruler position feedback and optional CNC controllers from DELEM, ESA or CYBELEC. Multiple tonnage and working-length configurations are available for different sheet metal bending applications.

As a professional press brake and plate rolling machine manufacturer, Pacific can assist buyers with:

  • Workpiece and process analysis
  • Press brake tonnage selection
  • CNC axis configuration
  • Crowning-system selection
  • Customized tooling
  • Factory acceptance testing
  • Operator training
  • Spare-parts and technical support

Send Pacific your material specifications and part drawings to receive a press brake configuration based on your actual production requirements rather than a generic machine recommendation.

Related News

share:

Table of Contents

Contact Us Now

Scroll to Top